Design Store

Adapting Digilent PmodCLP LCD to Cyclone 10 LP Development Kit with switches, push buttons, LEDs and “Hello C10LP” Display  

CategoryDesign Example
NameAdapting Digilent PmodCLP LCD to Cyclone 10 LP Development Kit with switches, push buttons, LEDs and “Hello C10LP” Display
DescriptionIn this design example, the Nios II processor is used to print “Hello C10LP” text to the LCD as well as providing the display of dip switches state (ON/OFF). The provided Optrex 16207 LCD Controller Core is used to control the LCD through Nios II.This design also include 4 push buttons which will trigger interrupt to Nios II upon pressed and blink LEDs according to push button pressed by user.
Operating SystemNone
IP Core
IP CoreHeading
IRQ MapperQsysInterconnect
Avalon-ST Bytes to Packets ConverterQsysInterconnect
Avalon-ST Channel AdapterQsysInterconnect
Avalon-ST Single Clock FIFOQsysInterconnect
Avalon-ST JTAG InterfaceQsysInterconnect
Avalon-ST Packets to Bytes ConverterQsysInterconnect
Reset ControllerQsysInterconnect
Avalon-ST Timing AdapterQsysInterconnect
Avalon Packets to Transaction ConverterQsysInterconnect
JTAG UARTConfigurationProgramming
Altera Avalon LCD 16207Peripherals
PIO (Parallel I/O)Other
MM InterconnectQsysInterconnect
Avalon-ST AdapterQsysInterconnect
Avalon-ST Error AdapterQsysInterconnect
Memory-Mapped DemultiplexerQsysInterconnect
Memory-Mapped MultiplexerQsysInterconnect
Avalon-MM Master AgentQsysInterconnect
Memory-Mapped Traffic LimiterQsysInterconnect
Avalon-MM Master TranslatorQsysInterconnect
Avalon-MM Slave AgentQsysInterconnect
Avalon-MM Slave TranslatorQsysInterconnect
Memory-Mapped RouterQsysInterconnect
Nios II Gen2 ProcessorNiosII
Nios II Gen2 Processor UnitNiosII
On-Chip Memory (RAM or ROM)OnChipMemory
System ID PeripheralOther
FamilyCyclone 10 LP
Adapting Digilent PmodCLP LCD to Cyclone 10 LP Development Kit with switches, push buttons, LEDs and “Hello C10LP” displayAdapting_Digilent_PmodCLP_LCD_to_Cyclone_10_LP_Development_Kit_with_switches,_push_buttons,_LEDs_and_"Hello_C10LP"_display
Development KitCyclone 10 LP FPGA Evaluation Kit
Installation Package

Note: After downloading the design example, you must prepare the design template. The file you downloaded is of the form of a <project>.par file which contains a compressed version of your design files (similar to a .qar file) and metadata describing the project. The combination of this information is what constitutes a <project>.par file. In releases 16.0 or newer, you can simply double click on the <project>.par file and Quartus will launch that project.

The second means to bring up the project template is through the New Project Wizard (File -> New Project Wizard). After entering the project name and folder on the first panel, the second panel will ask you to specify an empty project or project template. Select project template. You will see a list of Design Templates projects that you have loaded prior as well as various "Baseline Pinout Designs" that contain the pinout and settings for a variety of development kits. If you don't see your design template in the list, click on the link that states install the Design Templates circled below:

Browse to the <project>.par file you downloaded, click next, followed by Finish, and your design template will be installed and displayed in the Project Navigator pane in Quartus.

Note: When a design is stored in the Design Store as a design template, it has been previously regression tested against the stated version of Quartus software. The regression ensures the design template passes analysis/synthesis/fitting/assembly steps in the Quartus design flow.

At the command-line, type the following command:

quartus_sh --platform_install –package <project directory>/c10lp_lcd.par

Once the process completes, then type:

quartus_sh --platform –name c10lp_lcd

Download   (The download link will expire on Dec. 5, 2021, 9:32 a.m., please refresh the page to get a new link.)
Quartus Prime VersionDownload Quartus Prime v17.0
Quartus Prime EditionStandard

Last updated on June 22, 2018, 1:58 a.m.